ARK
MUSIC

Car Immobiliser Repair

Car immobilisers are an important anti-theft system that prevents unauthorised vehicle engines from running. The transponder chip in your smart key allows communication between the remote or key fob and your car's ECU.

Sometimes they stop working without a clear reason. Sometimes it's just a case of requiring new batteries for your key fob, but occasionally internal damage must be repaired by a locksmith for automotive or a car dealer.

Ignition Lock

The ignition lock is an integral part of your vehicle that holds your key in place, while letting the tumblers spin when you insert the key. It also locks the steering wheel to stop thieves from stealing your car. Your key could be unable to from starting your vehicle at first attempt, or it could get stuck in a position that won't allow it to move.

These kinds of problems usually arise from wear and tear from years of inserting and removing the key. A corroded or damaged cylinder may block or bind and the springs and pins inside could become misaligned. These issues will usually get worse with time.

Modern car keys include a chip inside the plastic top that transmits a signal to the vehicle's immobiliser system. The car will start if the chip's code is the same as that stored in the immobilizer. The chips may stop working due to a number of reasons, such as the batteries that are worn out on the key fob or simply deteriorating over time.

To fix this problem, locate a reputable automotive locksmith who is specialized in ignition and key systems and make an appointment. They will be able to identify and fix this fairly quickly. It's important to note that messing with the ignition or trying to open the steering wheel yourself may cause additional damage to your vehicle.

Ignition Cylinder

It's not unusual for the ignition cylinder to fail. This is because cars are full of moving mechanical components and are prone to wear and wear and tear.

If you notice that it is difficult to turn your key in the ignition cylinder, this could be a sign. Often this happens because the pins inside the tumbler wearing out over time. When this happens, it could interfere with starting the car, which could be a major issue.

A light that appears every time you turn the key is another indication that the ignition is not working. The light can be the result of a variety of issues. The easiest way to identify it is to contact an expert to take a look at the ignition system.

The transponder is located in the plastic that covers the thumbturn or bow of your key. If you have an old model, the blade is protruding from the remote. When you insert the key in the ignition, it transmits an electronic code to the car's immobilizer. The immobilizer then tries to match the code with one that has been recorded. If there is a problem with the transmission of these codes then your car won't start regardless of where you place the key in the ignition.

Ignition Wire

Modern cars are full of mechanical components which are susceptible to wear and tear. The ignition switch is just one such component. If the ignition switch fails then you will not be in a position to start your vehicle and you may notice that the previously working keys for the car remote or transponder no longer unlock the vehicle doors.

The ignition switch is a 4 wire device that is responsible for turning on the engine and Auto Keys R Us other accessories. The ignition switch has two wire sets one for the battery and another for the starter. When you turn the ignition key to "on", the switch pin closest to the key will switch on, sending current to the ignition coil and the starter.

To access the ignition switch, take off the steering wheel and remove the plastic clips which hold it in place. The next step is to locate the power lead wire from the battery in your car. It's a thick red wire that is constantly powered. The terminal end of the wire into the BATT terminal on the switch and ensure it is secured.

The other terminals are marked ACC IGN and ST. Check the service manual of your car or a wiring diagram to identify each terminal. Once you know the layout, you'll be able to connect each wire properly.

Immobiliser

Car immobilisers stop cars from starting without the right key. They function by sending a coded signal to the transponder chip on your key or Smart Key fob and an immobiliser module that is located in the car's ECU (Engine Control Unit). Only after both of these are in sync, will the engine be allowed to begin.

Modern cars are also equipped with remote locking systems which allows you to lock and unlock your vehicle, as well as remotely start the engine using C-V2X technology. This is a crucial security feature that shouldn't get overlooked.

The most common method used by thieves to steal cars is to "hot wiring" it after entering the vehicle. Hot wiring typically involves disconnecting the ignition cord before connecting the wiring manually. Immobilisers block this process by preventing ignition systems electronically through the computer.

If you're experiencing issues with your immobiliser first thing to examine is the battery on the key fob. If this isn't the issue, then you may be required to bring your car to an Auto Keys R Us repair shop or dealership. But, there's an alternative that is less expensive that you can use to get your vehicle's immobiliser working once more. See this video to learn how. This technique involves shorting the two wires of the OBDII connector to perform the handshake between ECUs in order to program new keys.